2006-2011 Camry Aurion · Service Manual BRAKE

REMOVAL

Removal / installation · Vehicles built Oct 2006 – May 2009

Versions by build date: Jun 2006 – Sep 2006 Oct 2006 – May 2009 from Jun 2009

HINT:
  1. Use the same procedures for the No. 2 parking brake cable assembly and No. 3 parking brake cable assembly.
  2. The procedures listed below are for the No. 3 parking brake cable assembly.


1. REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY

HINT:
Refer to the procedures up to "REMOVE PARKING BRAKE LEVER SUB-ASSEMBLY". (Click here)


2. REMOVE PARKING BRAKE PEDAL ASSEMBLY (for LHD)

HINT:
Refer to the procedures up to "REMOVE PARKING BRAKE PEDAL ASSEMBLY (for LHD)". (Click here)


3. REMOVE PARKING BRAKE PEDAL ASSEMBLY (for RHD)

HINT:
Refer to the procedures up to "REMOVE PARKING BRAKE PEDAL ASSEMBLY (for RHD)". (Click here)


4. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for Lever Type Parking Brake)

  1. C131912
    Using a screwdriver, pull up the parking brake lever claw.

  1. C132670E01
    Remove the lock nut, the No. 1 wire adjusting nut, and the No. 1 parking brake cable assembly from the parking brake lever sub-assembly.


5. REMOVE NO. 1 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)

  1. C132698
    Using a screwdriver, pull up the parking brake pedal claw.

  1. C132697
    Remove the lock nut and the No. 1 wire adjusting nut.

  1. C132696
    Using needle-nose pliers, remove the clip and the No. 1 parking brake cable from the parking brake pedal assembly.


6. SEPARATE NO. 3 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)

  1. C133446
    Separate the No. 3 parking brake cable assembly from the parking brake equalizer.


7. SEPARATE NO. 2 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)

  1. C133455
    Separate the No. 2 parking brake cable assembly from the parking brake equalizer.


8. REMOVE NO. 4 PARKING BRAKE CABLE ASSEMBLY (for Pedal Type Parking Brake)

  1. C132655
    Slide the rubber boot as shown in the illustration.

  1. C132657
    Remove the No. 4 parking brake cable assembly from the parking brake equalizer as shown in the illustration.


9. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2AZ-FE)

  1. Remove the 2 bolts, 2 nuts and center exhaust pipe assembly.

    A146049

  1. Remove the gasket from the front exhaust pipe.


10. REMOVE EXHAUST TAIL PIPE ASSEMBLY (for 2GR-FE)

  1. Remove the 4 nuts and 2 exhaust tail pipes.

    A146044

  1. Remove the 2 gaskets from the exhaust tail pipes.


11. REMOVE EXHAUST CENTER PIPE ASSEMBLY (for 2GR-FE)

  1. Remove the 2 bolts, 2 nuts and exhaust center pipe assembly.

    A146045

  1. Remove the gasket from the exhaust front pipe assembly.


12. REMOVE NO. 2 FRONT FLOOR HEAT LOWER INSULATOR (for 2AZ-FE)

  1. C132669
    Remove the 3 nuts and the No. 2 front floor heat lower insulator.


13. REMOVE REAR WHEEL

14. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY (for LHD)

  1. C132653
    Remove the 2 bolts and separate the rear disc brake caliper assembly.

    HINT:
    Do not disconnect the flexible hose from the disc brake caliper assembly.


15. REMOVE REAR DISC (for LHD)

  1. C132813E03
    Release the parking brake and put matchmarks on the rear disc and the axle hub.

  1. Remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn the shoe adjuster until the wheel turns freely.


16. REMOVE PARKING BRAKE SHOE RETURN TENSION NO. 1 SPRING (for LHD)

  1. C132651
    Using needle-nose pliers, remove the 2 parking brake shoe return tension No. 1 springs.


17. REMOVE PARKING BRAKE SHOE STRUT (for LHD)
  1. Remove the parking brake shoe strut and the parking brake shoe strut compression spring.


18. REMOVE NO. 1 PARKING BRAKE SHOE ASSEMBLY (for LHD)

  1. C133469
    Release the claw of the parking brake shoe hold down spring No. 1 cup.

  1. Remove the No. 1 parking brake shoe assembly as shown in the illustration.

  1. Remove the parking brake shoe hold down spring No. 1 cup, the parking brake shoe hold down spring, the parking brake shoe hold down spring No. 2 cup, and the parking brake shoe hold down spring No. 1 pin.


19. REMOVE PARKING BRAKE SHOE ADJUSTING SCREW SET (for LHD)

  1. C133473E01
    Remove the parking brake shoe adjusting screw set.

  1. Remove the parking brake shoe return tension No. 2 spring.


20. REMOVE NO. 2 PARKING BRAKE SHOE ASSEMBLY (for LHD)

  1. C133471
    Release the claw of the parking brake shoe hold down spring No. 1 cup.

  1. Remove the No. 2 parking brake shoe assembly as shown in the illustration.

  1. Remove the parking brake shoe hold down spring No. 1 cup, the parking brake shoe hold down spring, the parking brake shoe hold down spring No. 2 cup, and the parking brake shoe hold down spring No. 2 pin.

  1. C108700
    Using needle-nose pliers, disconnect the No. 3 parking brake cable assembly from the parking brake shoe lever.

    NOTICE:
    Be careful not to damage the No. 3 parking brake cable assembly.


21. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY (for LHD)

  1. C132666
    Remove the 2 bolts and disconnect the No. 3 parking brake cable assembly from the backing plate.


22. DISCONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY (for RHD)

  1. C141952
    Using needle-nose pliers, remove the clip.

  1. Turn and disconnect the No. 3 parking brake cable assembly as shown in the illustration.


23. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

  1. C138186E02
    Using needle-nose pliers, remove the clip from the No. 3 parking brake cable assembly.

  1. Remove 3 bolts (A), bolt (B), and nut (C), and disengage each claw.

    C132668E03

  1. Remove the No. 3 parking brake cable assembly from the body.

  1. C132667E01
    Remove the parking brake cable clamp.

← REMOVAL (Jun 2006 – Sep 2006)REMOVAL (from Jun 2009) →